233 lines
6.9 KiB
Markdown
233 lines
6.9 KiB
Markdown
## 1 - Hardware
|
||
**0.96inch OLED Module MC096GX**
|
||
|
||
|Name|Color 1|Color 2|Color 3|
|
||
|----|----|----|---|
|
||
|Disp Color|white|blue|yellow/blue Double Color|
|
||
|SKU|MC096GW|MC096GB|MC096GY|
|
||
|
||
|item|content|
|
||
|----|----|
|
||
|Size|0.96(inch)|
|
||
|Type|OLED|
|
||
|OLED Chip|SSD1306|
|
||
|Resolution|128*64 (Pixel)|
|
||
|Module Port|IIC，①-GND,②-VCC,③-SCL,④-SDA|
|
||
|Disp Area|21.744x10.864(mm)|
|
||
|Module Size|27.3x27.8(mm)|
|
||
|Viewing Angle|>160°|
|
||
|Work Temp.|-20℃~60℃|
|
||
|Save Temp.|-30℃~70℃|
|
||
|Operating Volt.|3.3V / 5V|
|
||
|Power Consumption|To be determined|
|
||
|Product weight (including packaging）|8 (g)|
|
||
|
||
|PIN|Mode|Note|
|
||
|----|----|----|
|
||
|1|GND|OLED Power Ground|
|
||
|2|VCC|OLED Power (3.3V~5V)|
|
||
|3|SCL|OLED IIC BUS timer signal|
|
||
|4|SDA|OLED IIC BUS date signal|
|
||
|
||
----
|
||
|
||
## 2 - Raspberry Pi 4B
|
||
|
||
#### (1). I2C Config
|
||
|
||
```
|
||
cat /boot/config.txt | grep i2c_arm
|
||
dtparam=i2c_arm=on
|
||
```
|
||
|
||
#### (2). PIN Connect
|
||
|
||
|PI GPIO NO.|OLED|PI|
|
||
|----|----|----|
|
||
|GND|GND|1|
|
||
|3|VCC|3V3|
|
||
|5|SDA|SDA|
|
||
|9|SCL|SCL|
|
||
|
||
#### (3). Install
|
||
|
||
```
|
||
sudo apt-get install python-pip python3-pip -y
|
||
sudo python -m pip install --upgrade pip setuptools wheel
|
||
sudo apt-get install python-pil python3-pil -y
|
||
sudo pip install Adafruit_GPIO
|
||
sudo pip install Adafruit_SSD1306
|
||
sudo pip install Adafruit_BBIO
|
||
|
||
#git clone https://github.com/adafruit/Adafruit_Python_SSD1306.git
|
||
git clone https://github.com/aiminickwong/Adafruit_Python_SSD1306
|
||
cd Adafruit_Python_SSD1306
|
||
sudo python setup.py install
|
||
sudo pip install RPi.GPIO
|
||
|
||
cd Adafruit_Python_SSD1306/examples/
|
||
cp Adafruit_Python_SSD1306/examples/stats.py /opt/
|
||
sudo python /opt/stats.py
|
||
```
|
||
|
||
#### (4). stats.py
|
||
|
||
```
|
||
# Copyright (c) 2017 Adafruit Industries
|
||
# Author: Tony DiCola & James DeVito
|
||
#
|
||
# Permission is hereby granted, free of charge, to any person obtaining a copy
|
||
# of this software and associated documentation files (the "Software"), to deal
|
||
# in the Software without restriction, including without limitation the rights
|
||
# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
||
# copies of the Software, and to permit persons to whom the Software is
|
||
# furnished to do so, subject to the following conditions:
|
||
#
|
||
# The above copyright notice and this permission notice shall be included in
|
||
# all copies or substantial portions of the Software.
|
||
#
|
||
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
||
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
||
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
||
# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
||
# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
||
# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
||
# THE SOFTWARE.
|
||
|
||
import time
|
||
|
||
import Adafruit_GPIO.SPI as SPI
|
||
import Adafruit_SSD1306
|
||
|
||
from PIL import Image
|
||
from PIL import ImageDraw
|
||
from PIL import ImageFont
|
||
|
||
import subprocess
|
||
|
||
# Raspberry Pi pin configuration:
|
||
RST = None # on the PiOLED this pin isnt used
|
||
|
||
# Note the following are only used with SPI:
|
||
DC = 23
|
||
SPI_PORT = 0
|
||
SPI_DEVICE = 0
|
||
|
||
# Beaglebone Black pin configuration:
|
||
# RST = 'P9_12'
|
||
# Note the following are only used with SPI:
|
||
# DC = 'P9_15'
|
||
# SPI_PORT = 1
|
||
# SPI_DEVICE = 0
|
||
|
||
# 128x32 display with hardware I2C:
|
||
#disp = Adafruit_SSD1306.SSD1306_128_32(rst=RST)
|
||
|
||
# 128x64 display with hardware I2C:
|
||
#disp = Adafruit_SSD1306.SSD1306_128_64(rst=RST)
|
||
|
||
# Note you can change the I2C address by passing an i2c_address parameter like:
|
||
|
||
disp = Adafruit_SSD1306.SSD1306_128_64(rst=RST, i2c_address=0x3C)
|
||
|
||
# Alternatively you can specify an explicit I2C bus number, for example
|
||
# with the 128x32 display you would use:
|
||
# disp = Adafruit_SSD1306.SSD1306_128_32(rst=RST, i2c_bus=2)
|
||
|
||
# 128x32 display with hardware SPI:
|
||
# disp = Adafruit_SSD1306.SSD1306_128_32(rst=RST, dc=DC, spi=SPI.SpiDev(SPI_PORT, SPI_DEVICE, max_speed_hz=8000000))
|
||
|
||
# 128x64 display with hardware SPI:
|
||
# disp = Adafruit_SSD1306.SSD1306_128_64(rst=RST, dc=DC, spi=SPI.SpiDev(SPI_PORT, SPI_DEVICE, max_speed_hz=8000000))
|
||
|
||
# Alternatively you can specify a software SPI implementation by providing
|
||
# digital GPIO pin numbers for all the required display pins. For example
|
||
# on a Raspberry Pi with the 128x32 display you might use:
|
||
# disp = Adafruit_SSD1306.SSD1306_128_32(rst=RST, dc=DC, sclk=18, din=25, cs=22)
|
||
|
||
# Initialize library.
|
||
disp.begin()
|
||
|
||
# Clear display.
|
||
disp.clear()
|
||
disp.display()
|
||
|
||
# Create blank image for drawing.
|
||
# Make sure to create image with mode '1' for 1-bit color.
|
||
width = disp.width
|
||
height = disp.height
|
||
image = Image.new('1', (width, height))
|
||
|
||
# Get drawing object to draw on image.
|
||
draw = ImageDraw.Draw(image)
|
||
|
||
# Draw a black filled box to clear the image.
|
||
draw.rectangle((0,0,width,height), outline=0, fill=0)
|
||
|
||
# Draw some shapes.
|
||
# First define some constants to allow easy resizing of shapes.
|
||
padding = -2
|
||
top = padding
|
||
bottom = height-padding
|
||
# Move left to right keeping track of the current x position for drawing shapes.
|
||
x = 0
|
||
|
||
|
||
# Load default font.
|
||
font = ImageFont.load_default()
|
||
|
||
# Alternatively load a TTF font. Make sure the .ttf font file is in the same directory as the python script!
|
||
# Some other nice fonts to try: http://www.dafont.com/bitmap.php
|
||
# font = ImageFont.truetype('Minecraftia.ttf', 8)
|
||
|
||
while True:
|
||
|
||
# Draw a black filled box to clear the image.
|
||
draw.rectangle((0,0,width,height), outline=0, fill=0)
|
||
|
||
# Shell scripts for system monitoring from here : https://unix.stackexchange.com/questions/119126/command-to-display-memory-usage-disk-usage-and-cpu-load
|
||
|
||
cmd = "hostname -I | cut -d\' \' -f1"
|
||
IP = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "top -bn1 | grep load | awk '{printf \"CPU Load: %.2f\", $(NF-2)}'"
|
||
CPU = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "free -m | awk 'NR==2{printf \"Mem: %s/%sMB %.2f%%\", $3,$2,$3*100/$2 }'"
|
||
MemUsage = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "df -h | awk '$NF==\"/\"{printf \"Disk: %d/%dGB %s\", $3,$2,$5}'"
|
||
Disk = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "echo $(uname -r |sed 's/Release-OPENFANS+//'|sed 's/v8//'|sed 's/202.//')$(cat /boot/version|awk -F'-' '{print $6}')"
|
||
Ver = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "/usr/bin/get_cpu|grep Freq|awk '{print $3}'|sed 's/Mhz/ Mhz/'"
|
||
Freq = subprocess.check_output(cmd, shell = True )
|
||
|
||
cmd = "/usr/bin/get_cpu|grep Temp|awk '{print $3}'"
|
||
Temp = subprocess.check_output(cmd, shell = True )
|
||
|
||
# Write two lines of text.
|
||
|
||
draw.text((x, top+0), "Freq: " + str(Freq), font=font, fill=255)
|
||
|
||
draw.text((x, top+8), "Temp: " + str(Temp), font=font, fill=255)
|
||
|
||
draw.text((x, top+16), str(CPU), font=font, fill=255)
|
||
|
||
draw.text((x, top+25), str(MemUsage), font=font, fill=255)
|
||
|
||
draw.text((x, top+35), str(Disk), font=font, fill=255)
|
||
|
||
draw.text((x, top+45), "IP: " + str(IP), font=font, fill=255)
|
||
|
||
draw.text((x, top+55), "Ver: " + str(Ver),font=font, fill=255)
|
||
|
||
# Display image.
|
||
disp.image(image)
|
||
disp.display()
|
||
time.sleep(.1)
|
||
```
|
||
|